I received the strategy to adorn my car battery from an aged typical motor vehicle magazine I observed years in the past — any person had wrapped classic-looking decals on a modern battery to protect the period of time-correct search of an aged Jag’s engine bay. I executed a related concept for a exciting tiny undertaking on my Civic Si, and it in fact arrived out wanting fairly sweet.
At the hazard of outing my un-ironic secret like for the Need to have For Speed: Underground aesthetic, I’ll acknowledge that I am massive into engine gown-up. About the decades I have painted plastic items, replaced lengths of wire loom just to modify their shade, made my own emblems to adhere on engine handles, and spent several hours agonizing above the orientation of stickers that nobody but me will at any time see. So if you’re questioning “who the hell would trouble decorating a car or truck battery” … it me.
But very seriously if you’re seeking for a quite easy attractive job or an additional layer of motor vehicle personalization, here’s how I decal’d my automobile battery to make it look cooler.
Here’s the battery as I acquired it when I acquired the automobile. It can be nothing specific.
I’d hardly ever read of this model and suspect it was not costly, but it is been fine. It doesn’t consider considerably juice to fireplace up a two-liter four-banger. This is a very effortless battery to transform the look of due to the fact it’s nice and basic — a little something like an Interstate with a lime-green major may well be more challenging to hide (if which is your prepare).
Anyway, my to start with shift was to remove the battery’s present sticker. Of study course, I could have just eradicated the ProMax model sticker and had a pleasant clean black brick, but that wasn’t further more than enough for me. I stuck it on a piece of paper I’ll hold in my car’s company data, just in scenario I have to have to reference it for some reason.
Then I discovered there was a warning label beneath that sticker — that arrived off much too, but I imagined it looked awesome so I stashed it experience-down for probable re-software.
The key to getting rid of stickers like this without the need of wrecking them or leaving a great deal of residue is to go slowly but surely, continually, at an angle, and normally consider to be grabbing as near to the nevertheless-stuck section as attainable.
My “design” is genuine very simple: I experienced masses of purple vinyl stripes laying all around from when I did the graphics on my Mitsubishi Montero, so all I needed to do was slap a purple line on there and possibly just one extra layer of a thing on prime of that. Just after a several seconds of imagining on what that could be, I determined that “51R” (the battery’s dimension team) would make sense. And I just so took place to have a set of white letter and quantity decals that suit within the pink striping beautifully.
Chopping the proper size of red was simple — these vinyl stripes have grids on their backside for painless measurement. I like to spritz the back again (sticky aspect) of vinyl like this with soapy water ahead of laying it down that tends to make it a good deal a lot more forgiving. You can slide it all-around a little if you really don’t place it at the exact position you required ideal absent.
You can do that the right way with a spray bottle, but for this goofy little challenge, I just lathered up some hand soap in my arms in the sink and then flicked it on to my vinyl strip below with my fingers. Certainly, you’ll want to be thorough receiving water near those people battery terminals, though. Dampness could guide to corrosion shock threat may well exist also but I believe it’s minimal.
Because my Civic’s battery has this small plastic frame close to it for some cause, I ran the purple stripe out down below the higher aspect of it and was capable to realize a tremendous thoroughly clean appear. It truly looks like it belongs on there! A plastic trim instrument was practical in sneaking the edges down.
The moment the stripe was laid I understood the battery’s warning label would really seem interesting and balance the “51R” emblem I prepared to make, so again on it went. It appeared loads sticky nonetheless right after becoming pulled off. Stickers are typically up for a 2nd software if you peel them up smoothly.
The letters and figures took a lot of endurance, but I’m pleased with the final outcome. I did the “5” initially, then the “R,” figuring I’d obtain a centered glimpse by earning them the identical length from the outdoors of the stripe and then placing the “1” in in between. After I laid my “1” down I made a decision I did not like my “5,” so I ripped it up and laid a new a single — fortunately I had a pair of more “5” decals in my sticker pack.
If I desired one more layer of precision listed here, I could have established down a strip of painter’s tape to align the letters along their tops or bottoms. But I was assured ample in my freehand application expertise and I’m happy with the top consequence.
Eventually, I’m also proud of the battery tie-down by itself and the accompanying nuts that hold it in spot. I assumed about obtaining just one of those shiny billet tie-downs, but truthfully, the stock Honda 1 has a simplicity to it that I uncover tasteful and its rubberized texture is nice. My auto experienced none at all when I acquired it, which is terrible information. You really do not want a cost-free-assortment motor vehicle battery due to the fact if you strike a bump just improper and it receives jostled you will have a direct pounds clanking around your engine bay. In any case, an OEM alternative was easy to resource cheaply from a Honda vendor.
The nuts that maintain it down, although, are an additional matter. Auto batteries are commonly detained by two threaded rods with nuts pinning them down. My emotion is that they never search pretty great, so I spent a extended time hunting at various varieties of nuts and fasteners that may well give the battery tie-down a more purposeful and finished overall look.
Immediately after exhaustive lookups at every neighborhood components retail store and a lot of internet websites, I settled on these plastic knurled knobs that are distinctive and industrial-wanting though however serving the important function of holding the battery in position. Especially, the “nuts” are essentially a pair of J.W. Winco 534-50-M8-SW Diamond Reduce Knurled Knobs, sized 30″ (1.18), M8 x 1.25 which I acquired from an outfit known as Worldwide Industrial.
I did have to minimize the threaded rod down a handful of inches for them to match, but that was conveniently done with a carbide hacksaw blade (experimented with a 1.5-inch Dremel reducing wheel as well, but in this circumstance, the hand saw was the transfer). They’re slightly cumbersome to attach because with the threaded rod currently being so limited it can be not as straightforward to get in put as it would have been usually. But I never anticipate removing the battery all that often, so it is really not a huge deal.
If you’re not the kind of person who understands projects like this, that is Alright (I’m surprised you go through this considerably!) but if you have been looking for a compact-but-enjoyable beauty mod you’re hereby welcomed to my thought for inspo. Besides essential automobile battery protection, the only true possible pitfall to consider about is that you may well need to continue to keep the manufacturing unit barcode or markings on your battery to make guarantee statements to turn one particular in for a main refund. I question it, but if that is a thing you are genuinely fearful about, think about at minimum holding the inventory sticker on hand if you peel it off.
Have any of you done some thing very similar, or recall the fake “Lucas Battery” sticker addresses I referenced at the commencing of this story?